Product Description：

---

NORIPHAN? N2K is a solvent-based two-component for the back of the printing IMD / FIM technology, screen printing ink can be used for PC material, such as Makrofol? And Bayfol? The PC chip. NORIPHAN? N2K: NORIPHAN? N2K printed in the back of the IMD / FIM technology, excellent performance:
- molding, thermal forming, or high-pressure molding
- injection molding process, as well as resistance to red ink when the temperature
- and the injection resins, such as PC, PC / ABS, and silicone resin adhesive properties of a good permanent
especially suitable for printing this ink sheet material (such as: 50��m of the sheet), sheet curling phenomenon can be avoided, but also suitable for IMD / FIM technology in the printing of metal coated film and suitable for chemical etching process
glossy appearance, gloss by the impact of printed material.
Color NORIPHAN? N2K non-toxic heavy metal pigments (in line with DIN EN 71, part 3).
NORIPHAN? N2K based on high-brightness and color, almost all colors can be obtained through the basic color matching.
Basic color NORIPHAN? N2K
109 Tartrazine
112 HF Huang
171 Transparent Yellow
213 Orange
308 Red
318 HF Transparent Red
320 red
372 HF transparent red
412 HF transparent pink
472 Purple
566 HF transparent blue
570 HF dark blue
669 transparent green
812 brown
945 HF White
952 HF Black
093 HF Varnish
HF = halogen
Special Inks special colored
NORIPHAN? N2K
770 HF ordinary silver
780 HF thick silver
790 HF-liang silver (ie, Indian hybrid)
944 HF cover the white
953 HF covered with deep black
954 HF Black
HF = halogen-free
silver ink with gold and other metal hue mixing.
Special effects inks other metal color, color effect, pearl effect, solar effects and other special pigments can be provided upon request.
Note that silver and special effects ink peeling strength (binding force) to be slightly lower than the other basic colors.
Back injection at the special effects ink may change the orientation of the pigment. Number of
mesh
recommended 77-48 threads / cm - 150-31 threads / cm (195-48 threads / inch -
380-31 threads / inch) polyester mesh. Stainless Steel Wire can be applied to special requirements.
Suggested printing silver mesh is as follows:
NORIPHAN? N2K 770 - 120-34 threads / cm (305-34 threads / inch) or less
NORIPHAN? N2K 780 - 77-48 threads / cm (150-31 threads / inch) or less
NORIPHAN? N2K 790 - 100-40 threads / cm (255-40 threads / inch) or less
stencil must use solvent-type light-sensitive glue. Use Baolong Norikop 8 HR-type light-sensitive glue
the production process in a long time to get excellent print results guaranteed.
Auxiliary requirements
hardener hardener NORIPHAN? N2K 005 in the pre-press to join, even stirred into the ink quantity
joined: 2 - 3%
mix well NORIPHAN? N2K and hardener NORIPHAN? N2K 005 activation of a mixture of small
life of 8-12 hours, depending on the temperature and humidity conditions.
Thinner
thinner NORIPHAN? N2K 090 (dry fast)
relieve dry agents relieve dry agents NORIPHAN? N2K 097 (medium dry)
relieve dry agents NORIPHAN? N2K 097/003 (dry slowly )
NORIPHAN? N2K 097/006 (dry very slowly)
slow-dried paste NORIPHAN? N2K 097/002 (medium drying rate)
NORIPHAN? N2K 097/007 (dry and very slow)
between additives may be necessary, any ratio mixed with each other.
General proposes to add the corresponding thinner 15 - 20%.
To print fine patterns, NORIPHAN? N2K 097/003 or NORIPHAN? N2K 097/006 relieve dry agents
can be used alone, or you can and slow dry paste NORIPHAN? N2K 097/002 or NORIPHAN? N2K 097/007 combined use. Proposal is as follows:
10 - 20% NORIPHAN? N2K slow-dried paste
5 - 10% NORIPHAN? N2K relieve dry agents
matte agent
NORIPHAN? N2K Matt Paste 098 adding amount: about 20 %
antistatic agents Norilin? C
used to prevent static electricity, especially when the ink in the printing of metal. Add volume: 0.5%
Defoamer Defoamer 9242
used to eliminate the color gradient of the defect may occur (concave point, bubbles). Add excess Defoamer 9242 will cause white spots.
Adding amount: Up to 0.5%
cleaning
recommended UNI-REIN A III cleaning wire and equipment.
Important conditions for printing materials and printing production decision to print the results. Therefore, we recommend that you must do pre-test products. Products because of different materials, different manufacturers, even if the same manufacturers, different batches and differences also exist between products, and some sheet anti-static additives such implied will also affect the ink adhesion.
Dry
NORIPHAN? N2K achieved by solvent evaporation drying. Chemical cross-linking process has been carried out, even in the drying rack.
Note:
film to protect the PC from the solvent effect, if a small amount of printing test also recommend the use of the tunnel dry. Drying rack drying is not recommended.