Products
IPX series
Product Description：
Empire IPX screen printing ink (corresponding to low odor environment of the two liquid rolling forming screen printing ink) IPX ink does not contain benzene, toluene, xylene, and isophorone ketone and other environmentally hazardous substances corresponds to a low odor environment forming with ink. PET and PC film with good adhesion. Has excellent heat resistance, rolling forming after machining and forming resin has good adhesion. Is suitable for the nameplate, and other fine print rolling forming two liquid reaction type of screen printing ink.
Use
* Easy adhesion treated PET film and PC film rolling forming printed with patterns.
* Calender forming acrylic, AS, ABS,, the PC / ABS resin, etc..
Feature
* Superior heat resistance of the coating can form two liquid reaction type ink.
* Printing film has the superior relief workability.
Can be cured in 90 ° C heating conditions rolling forming patience.
* Available in weather resistance, heat resistance, excellent color serial dilution / curing agent mixing / washing
* Before using ink to be fully stirring.
* Diluted F-003 solvent 10 to 15 percent, according to the printing conditions, the following solvents can also be used. F-001 (quick-drying), the F-003 (standard), Z-705 (slow drying type) * excessive dilution or the use of other solvents will reduce the printability and adhesion, should be avoided.
* Depending on the purpose, 100 ink, please add the following amount after mixing. 240 curing agent (standard) 220 200 hardener hardener hardener 106 IPX 10% 15% 16% 14%
* Allows time in the room temperature of 25 ° C, about 4 to 5 hours.
* More than enable time the ink will degrade performance, please do not re-use.
* For printing, screen washing (mesh detergent N) produced by this company.
* Auxiliaries SM40 Defoamer: improve the defoaming and leveling effect, use within 1 to 3 percent.
* Suitable for use in the printing of T-200 ~ 270 mesh screen.
* Printed T-250-mesh, per kilogram ink printed covers an area of approximately 35 square meters.
Drying / curing
* Must be heating and drying. Standard dry conditions for the oven at about 80 ° C for a 10-minute touch dry, and then printed on the IMB adhesive at 90 ℃ for 60 minutes final drying.
Due to the printing area, screen mesh, printing environment (temperature, humidity, etc.), the performance of the dryer different dry there will be changes in pre-production must be tested for confirmation. Equipped with setting color 000 low viscosity colorless 182 red 519 orange 821 purple 001 standard viscosity colorless 238 yellow 581 Rose 971 Black 168 Crimson 277 red Yellow 675 White 178 Red 391 Blue 791 Green Note
* For vacuum forming, pressure forming, forming metal mold forming, etc., as well as the printed sheet into a metal mold, injection molding resin into the integration of rolling forming, printing materials and patterns printing ink selection, printing conditions, The order of printing, drying methods and conditions, forming the choice of resin, metal mold design (the type and location of the sprue, sprue number), the injection molding condition setting, and so a combination of factors will affect the performance of the final product. So please fully test India, confirmed all the best condition after use.
* To enhance and forming the resin bonding, please use the Company's IMB-003 adhesive "and" the IMB-009 adhesive. "IMB-009 adhesive," applies to bond with mirror ink, "the IMB-003 adhesive applies to all ABS and PMMA molding resin. See the IMB-003 adhesive "and" the IMB-009 adhesive "manual.
Fire Control Law said
* The case of dangerous goods, oil, risk rating for the three security / custody
* To protect the skin and eyes, use safety gloves and protective glasses. If the ink stained skin, wash with soap and plenty. In addition, the case into the eyes of water (or warm) after the full cleaning, please go to the hospital to accept the doctor's diagnosis.
* Use Containers should be sealed on the dark and cool place.
* Prepare the MSDS, please obtain a copy of the MSDS before using this product read, understand user should be the responsibility before use.
Patience pilot projects to test conditions for test results adhesion JIS K 5600-5-6: ISO2409 (cross-line method), 1mm wide and 6 × 6, stripped with cellophane tape 0 (stripping) scratch hardness JIS K 5600-5 - 4: ISO15184 (pencil method), weight 750g, the coating no scratches on the hardness of F heat resistance ISO3248: 80 ° C, 400 hours to observe the appearance of the coating and stripping of abnormal heat water, JIS K 5600-6 -2: ISO2812-2, at 40 ℃ hot water soak for 48 hours, observe the appearance of the coating and stripping of abnormal acid soak for 7 hours in a 5% sulfuric acid and to observe the appearance of the coating and stripping of abnormal resistance to alkaline soak in 5% NaOH, 24 hours to observe the appearance of the coating and stripping of abnormal rubbing sexuality vibration abrasion test, KANAKIN3 number of cotton, 500 g load friction 500 to observe the appearance of the coating no abnormal resistance to alcohol sexuality vibration abrasion test, the KANAKIN3 No. cotton soaked with alcohol, 200 g load friction 50 times to observe the appearance of the coating without exception punch puncher exception Erikson test JIS K, 5600-8-2 (Erikson testing machine), no abnormal impact resistance JIS K 5600-5-3 DuPont impact test machine to observe the appearance of the coating, 50cm/500g without exception printing material: easy adhesion treated PET sheet (Dongshan production HK31WF) Ink: IPX 675 white dilution solvent: the F-003 10%, 10% of the printing screen 240 hardener: T-250-mesh dry conditions: oven 90 ° C, 60 minutes * on the patience of test results, test results in the company, not guaranteed values.
Empire IPX screen printing ink (corresponding to low odor environment of the two liquid rolling forming screen printing ink)